Laney Amplification RB5 User Manual Page 8

  • Download
  • Add to my manuals
  • Print
  • Page
    / 12
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 7
WARNING - THIS EQUIPMENT MUST BE
EARTHED.
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS.NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
PERSONNEL ONLY.
ATTENTION - REMPLACER LE FUSIBLE
SEULEMENT PAR LE MEME TYPE ET LE
MEME CALIBRE.
ATTENTION - DEBRANCHER LE CORDON
DALIMENTATION AVANT TOUTE
INTERVENTION.
AVIS - RISQUE DE CHOC ELECTRIQUE -
NE PAS OUVRIR.
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF
FIRE REPLACE ONLY WITH SAME TYPE AND RATED FUSE.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
TUNER OUT
FX RETURN
FX SEND
SERIAL
NUMBER
8 OHM
MINIMUM
IMPEDANCE
REFER TO USER MANUAL FOR
LOUDSPEAKER CONNECTIONS
MADE IN CHINA
DESIGNED IN THE UK BY LANEY
MODEL
RB5
FABRIQUE EN CHINE
FUSE RATING & SUPPLY VOLTAGE
䅘䥍啍 佗䕒 低单䵐呉低
㈴〠䅔呓†縵〯㘰⁈
www.laney.co.uk
Laney
POWE R TO TH E MUS IC
EXTENSION
LOUDSPEAKER
3
1
Page 8 /12 Page 9 /12
2
3
4
5
Power inlet socket. Connect to your power source. Make sure the specified voltage is correct for your country!
This drawer contains the main safety fuse for the unit.
USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL.
The mains fuse ratings are detailed in the specs section at the rear of this manual.
Serial Number and model of your unit.
This socket(s) should be used to connect an extension-cabinet. The impedance of the extension-cabinet must not be less
than 8 Ohms. Connecting cabinets that have a lower impedance than 8 Ohms will result in the amplifier overheating.
Continual use in this manner may cause permanent damage. Connecting a cabinet with an impedance of greater than 8
Ohms will cause no damage to the amplifier but will result in a reduced output level. (When using an extension cabinet the
internal speaker remains connected)
Socket for connecting external tuner. This output taken before any EQ so the Volume control may be turned down for silent
tuning.
Send and return sockets are provided for connecting external effects-units. You can also use the Send socket as a line out if you
wish.
REAR PANEL CONTROLS
OTHER FEATURES
SAMPLE SYSTEM
8 Ohms
Link
Model RB115
Power Rating 300W Program
Model RB115
Power Rating 300W Program
Serial Number:Serial Number:
Input
Laney
Power To The Music
www.laney.co.uk
DESIGNED IN THE UK BY LANEY
8 Ohms
Link
Model RB115
Power Rating 300W Program
Model RB115
Power Rating 300W Program
Serial Number:Serial Number:
Input
Laney
Power To The Music
www.laney.co.uk
DESIGNED IN THE UK BY LANEY
SAMPLE
Input
Output
Loudspeaker Cable
Tuner Input
BLOCK DIAGRAM
RB410
Laney
OPERATING INSTRUCTIONS
Laney
OPERATING INSTRUCTIONS
INTERNAL
LOUDSPEAKER
D.I. OUT
TUNER OUT
GAIN
INPUT
VOLUME
FX LOOP
SEND RETURN
OUTPUT
ON ACTIVE
LIMITER
SECTION
EQ SECTION
COMPRESSOR
SECTION
ACTIVE
POWER
AMP
This loop is a series type so all
your signal will go through your
FX unit.
1 2
5 64
6
NORMAL
HIGH
PAD
Your RB5 features a kick style design to enable you to use
it as a stage monitor, or a conventional straight combo.
Page view 7
1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments